Components
1.Capture antibody for IFNγ (0.50 mL). Supplied sterile.
2.Capture antibody for IL-2 (0.50 mL). Supplied sterile.
3.FITC conjugated detection antibody for IFNγ (lyophilised, resuspend in 0.55mL).
4.Biotinylated detection antibody for IL-2 (lyophilised, resuspend in 0.55mL).
5.Anti-FITC antibody HRP conjugate (100 µL).
6.Streptavidin Alkaline Phosphatase conjugate (50 µL).
7.Bovine Serum albumin
8.Dry skimmed milk:non sterile Elispot / Liquid sterile milk: sterile Elispot.
9.50 x concentrate AEC substrate buffer (1mL).
10.10 x concentrate buffer for the preparation of AEC buffer (5mL).
11.Ready-to-use BCIP/NBT substrate buffer (50mL).
12.96 PVDF-bottomed-well plates (5 if ordered).
Material not included
1.96 PVDF-bottomed-well plates.
2.Cell culture media.
3.CO2 incubator.
4.70% ethanol.
5.Tween 20.
6.Phosphate buffered saline.
7.ELISPOT reading system.
Reagent Preparation
1.Detection antibody:Reconstitute the lyophilised antibody with 0.55mL of distilled water. Gently mix the solution and wait until all the lyophilised material is back into solution.
2.Streptavidin alkaline phosphatase:Dilute 1/1000 in PBS 1% BSA.
3.Phosphate buffered saline (10X Concentrate solution):For 1 liter weight : 80g NaCl ; 2g KH2PO4 ; 14.4g Na2HPO4 2H2O. Add distilled water to 1 liter. Check that pH is comprised between 7.4 +/- 0.1. Dilute the solution to 1X before use.
4.Skimmed milk in PBS:For one non-sterile plate dissolve 0.2g of powder in 10mL of 1X PBS;For one sterile plate dilute 5ml of liquid milk in 5ml of 1X PBS.
5.1% BSA in PBS:For one plate dissolve 0.2 g of BSA in 20 mL of 1X diluted PBS.
6.0.05% Tween in PBS:For one plate dissolve 50µl of Tween 20 in 100 ml of 1X diluted PBS.
7.35% ethanol in water:For one plate mix 3.5 ml of ethanol with 6.5 ml of distilled water.
8.AEC buffer:For one plate mix 1 ml of AEC buffer A with 9 ml of distilled water. Then add 200µl of AEC buffer B.
Assay Procedure
1.Incubate PVDF-bottomed-well plates with 25µl / well of 35% ethanol for 30 sec at room temperature.
2.Empty wells and wash three times with 100µl / well of PBS.
3.Pipette 100µl of IFNγ capture antibody and 100µl of IL-2 capture antibody in 10 mL of plain PBS. Mix and dispense 100 µl into each well, cover the plate and incubate overnight at +4°C.
4.Empty wells and wash once with 100 µl of PBS.
5.Dispense 100 µl of skimmed milk in PBS into wells, cover and incubate for 2 hours at room temperature.
6.Empty wells by flicking the plate over a sink and tapping it on absorbent paper.
7.Wash plate once with PBS.
8.Dispense into wells 100 µl of cell suspension containing the appropriate number of cells and appropriate concentration of stimulator. Cells may have been previously in-vitro stimulated (Indirect ELISPOT). Cover the plate with a standard 96-well plate plastic lid and incubate cells at 37°C in a CO2 incubator for an appropriate length of time (15-20 hours).
9.Empty wells by flicking the plate over a sink and gently tapping it on absorbent paper.
10.Dispense 100µl of PBS-0.05% tween 20 into wells and incubate for 10 min at +4°C.
11.Wash wells three times with PBS-0.05% tween 20.
12.For 1 plate dilute 100µl of reconstituted IFNγ detection antibody and 100µl of reconstituted IL-2 detection antibody into 10 mL of PBS containing 1% BSA. Dispense 100µl into wells, cover the plate and incubate 1 hour 30 min at 37°C.
13.Empty wells and wash three times with PBS-0.05% tween 20.
14.For 1 plate dilute 20µl of anti-FITC HRP and 10 µl of streptavidin-Alkaline phosphatase conjugates into 10 mL of PBS-1% BSA.Dispense 100µl of the dilution into wells. Seal the plate and incubate for 1 hour at 37°C.
15.Empty wells and wash three times with PBS-0.05% tween 20.
16.Peel off the plate bottom; wash three times both sides of the membrane under running distilled water. Remove all residual buffer by repeated tapping on absorbent paper.
17.Prepare AEC buffer (see reagents preparation). Dispense 100µl of solution in wells.
18.Let the colour reaction proceed for 5-20 min at room temperature. When the spots have developed empty the buffer into an appropriate tray.
19.Wash three times both sides of the membrane with distilled water. Remove residual water by tapping the plate on absorbent paper. 20.Dispense 100µl of ready-to-use BCIP/NBT buffer into wells.
21.Let the colour reaction proceed for about 5-20 min at room temperature. When spots have developed, empty the buffer into an appropriate tray.
22.Wash thoroughly both sides of the membrane with distilled water
23.Dry the membrane by repeatedly tapping the plate on absorbent paper. Store the plate upside down so no remaining liquid will go back on the membrane. Read spots once the membrane is dried. Note that spots may become sharper after one night at +4°C.
Accession Number
NP_032363.1
Storage Comment
If not used within a short period of time, reconstituted detection antibody should be aliquoted and stored at -20°C.
Expiry Date
at least one year at -20°C
Note
Select online data sheet information is drawn from bioinformatics databases, occasionally resulting in ambiguous or non-relevant product information. It is the responsibility of the customer to review, verify, and evaluate the information to make sure it matches their requirements before purchasing the kit. Our ELISA Kit assays are dynamic research tools and sometimes they may be updated and improved.
Restrictions
For Research Use Only. Not for use in diagnostic procedures.